| Część nr | Producent | Zastosowanie |
|---|
| DG425AK | MaximIC | Improved low-pover, CMOS analog switches with latches |
| MAX820SCSE | MaximIC | Microprocessor and non-volatile metory supervisory circuit. Reset threshold 2.91V. Reset and low-line threshold accuracy +-2% |
| MAX301MLP | MaximIC | Precision, dual, high-speed analog switch. |
| MAX3241ECWI | MaximIC | +-15kV ESD-protected, down to 10nA, 3.0V to5.5V, up to 1Mbps, true RS-232 transceiver. |
| MAX1201CMH | MaximIC | +5V single-supply, 2.2Msps, 14-bit self-calibrating ADC |
| DG200AC/D | MaximIC | Dual monolithic SPST CMOS analog swith |
| MAX3664EUA | MaximIC | 622Mbps, ultra-low-power, 3.3V transimpedance preamplifier for SDH/SONET. |
| MAX642AESA | MaximIC | +12V fixed output, 10W CMOS step-up switching regulator. 5% output accuracy |
| MAX799CSE | MaximIC | Step-down controller with synchronous rectifier for CPU power. 3.3V/5V or adjustable main output. Regulates negative secondary voltage (such as -5V). |
| MAX6337US19D3-T | MaximIC | Ultra-low-voltage, low-power microprocessor circuit with manual reset (reset output active-low, open-drain) . Reset threshold(typ) 1.9V, reset timeout(min) 100ms. |
| MAX414BESD | MaximIC | Quad, 28MHz, low-noise, low-voltage, precision op amp. |
| MAX6321HPUK29CZ-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 2.930V, reset timeout(min) 140ms, watchdog timeout(typ) 25.6sec |
| MAX1638EAG | MaximIC | High-speed step-down controller with synchronous rectification for CPU power |
| MAX2267EUE | MaximIC | 2.7V, single-supply, cellular-band linear power amplifier. Low average CDMA current consumption in typical urban scenario 55mA. TSSOP-EP 5mm x 6.4mm. |
| MAX233AEPP | MaximIC | +5V-powered, multichannel RS-232 driver-receiver. |
| MAX233ACWP | MaximIC | +5V-powered, multichannel RS-232 driver-receiver. |
| MAX819LCUA | MaximIC | +5V microprocessor supervisory circuit. Reset threshold 4.65V, active-low reset, backup-battery switchover, power-fail comparator, battery freshness seal, manual reset input. |
| MAX6348XR45-T | MaximIC | Microprocessor supervisory circuit (reset output active-low, open-drain). Reset threshold (typ) 4.500V. Order increment 10k |
| MAX820LCPE | MaximIC | Microprocessor and non-volatile metory supervisory circuit. Reset threshold 4.62V. Reset and low-line threshold accuracy +-2% |
| MAX667EPA | MaximIC | +5V/programmable low-dropout voltage regulator |
| MAX6309UK45D2-T | MaximIC | Multiple-input, programmable reset IC (push/pull reset output,factory-set reset threshold on Vcc,1 additional undervoltage reset input,manual-reset input).Factory-trimmed reset thresholds 4.388(min),4.613(max) Nominal timeout period 20ms. |
| MAX3483EESA | MaximIC | 3.3V-powered, +-15kV ESD-protected, 15Mbps and slew-rate-limited true RS-485/RS-422 transceiver. Guaranteed data rate 0.25Mbps. Supply voltage 3.0V to 3.6V |
| MAX792RCPE | MaximIC | Microprocessor and non-volatile metory supervisory circuit. Reset threshold 2.61V |
| MX7824UQ | MaximIC | CMOS, high-speed, 8-bit ADC with multiplex. Error (LSB) +-1/2 |
| MAX9005EUA | MaximIC | Low-power, high-speed, single-supply op amp + comparator. Op-Amp gain stability 10V/V. Op-Amp gain bandwidth 8MHz. |
| MAX6309UK31D3-T | MaximIC | Multiple-input, programmable reset IC (push/pull reset output,factory-set reset threshold on Vcc,1 additional undervoltage reset input,manual-reset input).Factory-trimmed reset thresholds 3.003(min),3.157(max) Nominal timeout period 140ms. |
| MAX6318LHUK26CW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 2.630V min, reset timeout 140ms, typ watchdog timeout 6.3ms |
| MAX6501UKP035-T | MaximIC | Low-cost, +2.7V to +5.5V micropower temperature switch. Output stage open-drain. Standard temperature threshold(C) +35. |
| MAX6317HUK36CX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 3.600V, min reset timeout 140ms, typ watchdog timeout 102ms |
| MAX518BMJA | MaximIC | 2-wire serial 8-bit dual DAC with Rail-to-Rail outputs. TUE(LSB) 1.5. |
